JBC-AL250-B焊接烙鐵自動送錫手柄
產品價格：￥1520（人民幣）
商鋪名稱：貴州海躍通機電科技有限公司
聯系人：左應海（先生）
聯系手機：
固定電話：
企業郵箱：1113585224@qq.com
聯系地址：貴州省貴陽市觀山湖區長嶺北路金融城max-b座12-22
郵編：5555
聯系我時，請說是在五金機電網上看到的，謝謝！
商品詳情
1. Low Temperature Soldering:
High Power / mass ration tips and integrated
heater / thermocouple delivers the best thermal
recovery in the market along with lower soldering
temperatures.
2. Read & Feed:
We use one wire buried deep in the tip of the
copper to “read & feed.” Our thermocouple
and heating element are one in the same and
are microprocessor driven over a sensor at 60
hertz (60x a second) utilizing up to 140 watt
transformer. This is why our thermal performance
cannot be matched.
3. Initial Heat Up:
A conventional station takes between 10 to 90
seconds to reach 360° C. Any JBC station with
a T210 hand piece reaches this temperature in
only two seconds.
4. Outstanding Tip Life:
Lasting up to five times longer as soon as
the soldering iron is left in the stand, the tip
temperature automatically drops to 200° C,
decreasing oxidation and wear. Resulting in a
working life three to five times longer than that
of the conventional tip. When the soldering iron
is taken out of the stand again, the working
temperature is instantaneously reached.
NOTE: It varies by tip geometry, temperature
settings, solder, flux, and the person using it;
However generally, it ranges between 25,000
and 100,000 solder joints.
5. Quick Change Over Tips:
No tools needed to change the tip. Just place in
holder, pull and insert the new tip. Reduces your
idle time while increasing operator safety.
6. Ergonomic Design:
The JBC soldering iron are currently the lightest,
smallest and most ergonomic hand piece
available. Offering the shortest tip to hand
distance and a higher working performance.
7. Process Control:
Regain control of your process! Set temperatures
limits, read counters, block the station with PIN
or block the keypad.
8. Intelligent Heat Management:
Extend tip life by reducing temperature and
reduce energy usage to 10 watts during sleep
and 4 watts when hibernating.
9. Easy Calibration:
Since JBC technology is microprocessor driven,
it not necessary to recalibrate any of the JBC
stations but, if required, calibration of the
soldering tip can easily be done by using TI 2800
Thermometer and the temperature adjustment
featured in the station’s menu.
10. Improved Productivity:
The JBC technology gives an 80% improvement
over the performance of the best soldering
station available in the market. In the following
graphs, based on practical test, we show this
superiority.
High Power / mass ration tips and integrated
heater / thermocouple delivers the best thermal
recovery in the market along with lower soldering
temperatures.
2. Read & Feed:
We use one wire buried deep in the tip of the
copper to “read & feed.” Our thermocouple
and heating element are one in the same and
are microprocessor driven over a sensor at 60
hertz (60x a second) utilizing up to 140 watt
transformer. This is why our thermal performance
cannot be matched.
3. Initial Heat Up:
A conventional station takes between 10 to 90
seconds to reach 360° C. Any JBC station with
a T210 hand piece reaches this temperature in
only two seconds.
4. Outstanding Tip Life:
Lasting up to five times longer as soon as
the soldering iron is left in the stand, the tip
temperature automatically drops to 200° C,
decreasing oxidation and wear. Resulting in a
working life three to five times longer than that
of the conventional tip. When the soldering iron
is taken out of the stand again, the working
temperature is instantaneously reached.
NOTE: It varies by tip geometry, temperature
settings, solder, flux, and the person using it;
However generally, it ranges between 25,000
and 100,000 solder joints.
5. Quick Change Over Tips:
No tools needed to change the tip. Just place in
holder, pull and insert the new tip. Reduces your
idle time while increasing operator safety.
6. Ergonomic Design:
The JBC soldering iron are currently the lightest,
smallest and most ergonomic hand piece
available. Offering the shortest tip to hand
distance and a higher working performance.
7. Process Control:
Regain control of your process! Set temperatures
limits, read counters, block the station with PIN
or block the keypad.
8. Intelligent Heat Management:
Extend tip life by reducing temperature and
reduce energy usage to 10 watts during sleep
and 4 watts when hibernating.
9. Easy Calibration:
Since JBC technology is microprocessor driven,
it not necessary to recalibrate any of the JBC
stations but, if required, calibration of the
soldering tip can easily be done by using TI 2800
Thermometer and the temperature adjustment
featured in the station’s menu.
10. Improved Productivity:
The JBC technology gives an 80% improvement
over the performance of the best soldering
station available in the market. In the following
graphs, based on practical test, we show this
superiority.
